SmartFan® Nimbus-HP

AC Motor Speed Control for Fans, Pumps and Motors

SmartFan Nimbus-HP AC Motor Speed Control

Fig. 1: Nimbus-HP AC Motor Speed Control model TRC1800-F

Fig. 2: Nimbus-HP AC Motor Speed Control with cover model TRC1800E-F

Nimbus-HP AC Motor Speed ControlOperation/Installation Manual

SmartFan Nimbus-HP is a TRIAC based fan, pump and AC motor speed control designed for OEM applications in HVAC, electronic and industrial control markets. The Nimbus-HP AC motor speed control automatically varies single phase motors that have been approved for voltage control by the motor manufacturer. Nimbus-HP regulates motor speed from a control signal (2-10 VDC, 4-20mA) or up to three remote temperature sensors (thermistor). Typical AC motor speed control applications include: humidity control, clean room pressurization, equipment cooling, heat exchangers, exhaust ventilators, pumps, duct fans & blowers.

On-board programming allows the setting of many parameters providing maximum flexibility. Special and custom AC motor speed control configurations are available.

Benefits of using SmartFan Nimbus-HP AC motor speed control include acoustical noise reduction, environmental (humidity, temperature or pressure) regulation, greater product reliability, increased
fan life, improved safety and energy savings

CAUTION: SmartFan AC motor speed controls are designed for OEM (Original Equipment Manufacturers) and are not intended for end-user or after-market applications. SmartFan AC motor speed controls should only be used with compatible induction motors: Permanent Split Capacitor (PSC) or Shaded Pole. All AC motors must be approved by the motor manufacturer or thoroughly validated prior to use. Attempting to control a fan or motor that is not compatible could cause excessive heating and/or permanent damage to the motor.

Control Comparison & Motor Efficiency
See technical article on how the Nimbus-HP AC motor speed control compares to other controller technologies.

 

Specifications – Nimbus-HP AC Motor Speed Control

  • Power source: 85 – 300 VAC, automatically detected
  • Frequency: 47-64 Hz, automatically detected
  • Output power ratings at 65°C: 8 to 18 Amps
  • Motor type: Induction either permanent split capacitor (PSC) or shaded pole motors that have been approved for voltage control by the motor manufacturer
  • Input power and motor connections: 1/4″ quick connects
  • Control signal, sensor and alarm connections: Terminal Block
  • Full voltage start pulse
  • Storage temperature: -40°C to 125°C
  • Operating temperature: -20°C to 65°C
  • Temperature accuracy and hysteresis: 2°C
  • Weight: 1.25 lb. (567 grams)
  • Weight with cover: 1.90 lb. (862 grams)
  • RoHS (6/6) compliant
  • Agency approvals pending

Features – Nimbus-HP AC Motor Speed Control

  • AC motor speed control based on:
    • 4-20 mA control signal
    • 2-10 VDC control signal
    • Up to three remote temperature sensors (supplied separately)
    • Dual control option (i.e. temperature and humidity)
  • Programmable temperature control mode options:
    • Four full speed temperature settings
    • Two control temperature slopes
    • Four idle speed settings
  • Programmable fan/motor turn off at idle
  • 64 fixed speed settings
  • Remote alarm signal to indicate loss of control signal or over temperature condition
  • Optional metal cover

Part Numbering – Nimbus-HP AC Motor Speed Control

Part No. Power Source Output Power Rating at 65°C Enclosure
TRC1800-F 85-300 VAC 18 Amps No
TRC1800E-F Yes

Manual Pages – Nimbus-HP AC Motor Speed ControlOperation/Installation Manual

Use the links below for addtional manual pages or for a complete manual or click on the Operation/Installation Manual PDF link above.

Nimbus-HP – your choice for AC motor speed control for Fans, Pumps and Motors

Back to top
Control Resources
For Engineers, by Engineers.
Since 1984.
Control Resources Inc., 11 Beaver Brook Road, Littleton, MA 01460 USA • Tel: 978-486-4160 Fax: 978-486-4772 • Email: sales@controlres.com